Updated 20 November 2026.
The outline of the 2027 MotoGP technical regulations narrows the front fairing, moves its nose back, lowers the rear end and brings any aerodynamics behind the rider into the homologation system. This page sets each change beside the nearest 2026 provision, with the article numbers from the FIM’s 2026 regulations, and lists what the FIM has not yet published. It is part of our 2027 series: the MotoGP 2027 guide covers the whole season, and our MotoGP 2027 technical regulations page covers every other technical rule.

Regulatory status
- Ratified: the FIM Grand Prix Commission ratified the outline of the 2027 MotoGP technical regulations at its meeting in Jerez on 26 April 2024 and issued it on 6 May 2024. Article 2.4.4.7 of that outline carries the aerodynamic changes [1].
- Not amended: no Commission decision published by the FIM up to 17 November 2026 that we found amends, delays or reverses an aerodynamic item in that release. The only later decision to mention aero bodies, on 23 September 2026, freezes Moto2 aero bodies at their 2026 designs for 2027 and does not concern MotoGP [3]. Press coverage in September 2026 repeats the MotoGP aero items unchanged [8].
- Not yet in the rulebook: the FIM has not published a 2027 edition of its Grand Prix Regulations. The public book is the 2026 edition, updated on 13 September 2026 [2]. If the FIM follows last year’s timing, a 2027 edition will appear around the end of January or in February 2027; the 2026 edition is dated 31 January 2026.
- How to read the numbers: the 2026 article numbers below come from that book. The book numbers the clauses inside article 2.4.4.7 (bodywork) from 1 to 10, after preliminary items i to v. This page writes them in the form “2.4.4.7.2” for clause 2, where the book itself writes “see 10.” [2].
2026 against 2027
| Rule | 2026 | 2027 | 2026 article |
|---|---|---|---|
| Width of the front fairing | Maximum 600 mm above the Reference Line, 550 mm below it. The Reference Line is 550 mm above ground | Maximum width of the high portion falls to 550 mm | 2.4.4.7.2 |
| Rear end height | Parts behind a vertical line 500 mm ahead of the rear edge of the rear tyre cannot exceed 1,250 mm in height | Falls to 1,150 mm | 2.4.4.7.2 |
| Nose | Bodywork may not extend forward of a vertical line 150 mm behind the front edge of the front tyre | Foremost point of the front fairing moved back 50 mm | 2.4.4.7.3 |
| Rearward taper of the front fairing aero appendices | The release does not say which 2026 dimension this refers to; the main fairing’s maximum outline is set by templates | Narrows; no figure published | 2.4.4.7.2 (templates, Appendix General Fig. 3 and 4) |
| What is homologated | Four components: Front Fairing, Front Fender, Area “A” and Other Aero Body parts | The release says any aerodynamics behind the rider must be homologated as part of the Aero Body | 2.4.4.7.10 |
| Updates | One update per component per rider at any time in the season (clause c), within the concession allowance of one aero update per rider per season in Ranks A to C and two in Rank D (2.4.2.5); the book does not say how the two combine | “One update per season” (the release’s wording; whether the unit is a rider or a manufacturer is not stated) | 2.4.4.7.10 (clause c) and 2.4.2.5 |
What article 2.4.4.7 limits in 2026
Article 2.4.4.7 caps the size of the bodywork before it regulates what must be approved. Three of its limits are changed in the 2027 outline. A fourth group, ground clearance and moving parts, is context [2].
Width. The Aero Body may not exceed 600 mm in width above the Reference Line, or 550 mm below it. The Reference Line is a horizontal line 550 mm above ground level (2.4.4.7.2). The figure of 600 mm is a limit, not a measured width. The 2027 release states the new figure as 550 mm for the “high portion” of the front fairing. The 2026 limit below the Reference Line is already 550 mm. The release does not say whether the line or the lower limit changes [1, 2].
Rear height. In a side view, the parts of the machine behind a vertical line 500 mm ahead of the rear edge of the rear tyre cannot exceed 1,250 mm in height. In a top view they must stay inside a taper 450 mm wide at that line and 200 mm wide at the rear edge of the tyre (exhaust pipes and close-fitting covers excepted); unsprung parts such as the swingarm carry a separate 400 mm width limit (2.4.4.7.2). The side-view drawing in the appendix, General Fig. 2, marks the 1,250 mm height [2]. The 2027 release changes the height only, from 1,250 mm to 1,150 mm. It does not mention the 450 mm and 200 mm widths [1].
Nose. Bodywork may not extend forward of a vertical line drawn 150 mm behind the front edge of the front tyre (2.4.4.7.3) [2]. The 2027 release moves the foremost point of the front fairing back 50 mm but does not state the resulting position, so this page does not calculate one [1].
Ground clearance and moving parts. No part may be closer than 50 mm to the ground, or 35 mm for Aero Body parts in Area “A” when the machine is checked in the “down” position, and none may be behind a vertical line at the rear edge of the rear tyre (2.4.4.7.5). Moving aerodynamic devices are prohibited: an Aero Body part may deflect no more than 10 mm under a 50 N load (2.4.4.7.8) [2]. The 2027 release mentions neither.
The Aero Body and the four components
The 2026 regulations define the MotoGP Aero Body in article 2.4.4.7.10. It is the part of the bodywork directly hit by the oncoming air and not in the wake of the rider’s body or of other bodywork. That means the whole external shape of the Front Fairing and Front Fender, plus the inner surfaces of both that the oncoming air reaches. The windscreen, cooling ducts and engine intake ducts are exempt [2].
The definition reaches two further groups. “Other Aero Body parts” are of two kinds: parts that do not belong to the fairing or fender but are still directly hit by the oncoming air and not in the wake of the rider or other bodywork, such as handguards; and parts ahead of the rider that taper towards the rear in horizontal cross-section, such as drop-shaped fork covers. And any part belonging to Area “A” counts if it has design elements not strictly necessary for the rider to control the machine or for the wheels to be connected with proper stiffness. Area “A” is the rectangle, in side view, between the swingarm pivot centre and the back of the rear wheel, and between 50 mm above the ground and the rear wheel spindle centre. A swingarm shaped for extra functions, or a swingarm attachment, falls into it. Sensors, wiring, rear brake cooling ducts and close-fitting exhaust covers do not [2].
That gives four components: Front Fairing, Front Fender, Area “A” and Other Aero Body parts. Some of the machine’s rear end is therefore already homologated in 2026.
Approval and updates in 2026
Approval works as follows under article 2.4.4.7.10 [2]:
- A manufacturer delivers either full 3D CAD models of all outer Aero Body surfaces (in .stl format) or a sealed reference sample of each part to the Technical Director, normally before the close of technical control at the first event of the season. CAD models must mark the “Aero Line”, a horizontal line 300 mm above a line touching the lowest point of the lower body profile. This is a different reference line from the 550 mm Reference Line in the width rule.
- Approval is per rider, so two riders on the same make may run different Aero Bodies (clause b).
- One update per component is allowed at any time during the season, for each rider. Area “A” and the Other Aero Body parts each count as one component, so any change to it, including adding or removing a part, is that component’s one update (clause c).
- An update may reuse a previously approved component, each rider may have at most two Aero Bodies available, and initial and updated components may be mixed (clause c).
- Material may be removed for clearance or cooling at the Technical Director’s discretion, but not added (clauses f and g).
- A manufacturer in its first season in the MotoGP class may make an unlimited number of updates (clause h).
The concession table in article 2.4.2.5 also sets an allowance. In Ranks A, B and C it is one aero update per rider per season. In Rank D it is two, with one existing specification discarded when the second is taken [2].
What 2027 changes
The 6 May 2024 release states the changes under the heading “Reduction of aero surfaces”, article 2.4.4.7 [1]:
- The maximum permitted width of the high portion of the front fairing Aero Body falls from 600 mm to 550 mm.
- The maximum rear end height falls from 1,250 mm to 1,150 mm.
- The foremost point of the front fairing, the nose, moves back 50 mm.
- The rearward taper of the front fairing aero appendices narrows.
Under the sub-heading “Homologation of aero surfaces”, the release adds that the rear end of the machine, meaning any aerodynamics behind the rider, must be homologated as part of the Aero Body, and that manufacturers will be permitted one update per season [1].
On the release’s wording, the clear change is one of scope. Homologation, per-rider approval and an update allowance already exist in 2026, and the release extends the approval to any aerodynamics behind the rider, not only the parts that meet the 2026 definition. It states the update allowance as one per season. Whether per-rider approval and the per-component update rule carry over is not stated.
How the rules reached this point
Selected Commission decisions on aerodynamics, in date order. This is not a complete history: the dates on which Area “A” and the Other Aero Body parts entered the regulations are not shown.
| Date | Decision | Content |
|---|---|---|
| 25 June 2016 | Commission meeting, Assen | Aerodynamic wings banned in the MotoGP class from 2017; wings complying with the 2016 regulations may be used for the rest of that season [4] |
| 15 October 2016 (published on MotoGP.com on 18 October) | Commission decision, “MotoGP Class Aerodynamic Evolution” | From 2017, initial fairing and front mudguard designs are homologated by the Technical Director at the first event; one upgrade each per rider per season [5] |
| 15 July 2019 (published on MotoGP.com on 19 July) | Commission electronic meeting | Aero Body regulations revised and updated from 2020; manufacturers had until the first event of 2020 to design their components [6] |
| 6 May 2024 | Technical regulations outline | The 2027 aero reductions and rear-end homologation [1] |
Reported analysis
Motor Sport magazine quoted Aprilia technical director Fabiano Sterlacchini in January 2026: “I believe we will have between 30% and 50% less downforce” [7]. It is one engineer’s estimate. We found no downforce figure in any FIM document.
What has not been published
- The detailed 2027 regulation text. The 6 May 2024 release is an outline, and the FIM’s 2027 edition has not appeared.
- The new nose position as a measurement, and the Reference Line and below-line width limit for 2027.
- A figure for the narrowing of the rearward taper of the front fairing aero appendices, and which 2026 dimension it replaces.
- Whether the 2026 rear taper (450 mm and 200 mm) changes.
- How the one update per season relates to the concession table in article 2.4.2, and whether the first-season manufacturer exemption and the Rank D allowance of two updates continue.
- How “behind the rider” is defined, and the 2027 approval deadline and submission form.
This page is updated whenever the Commission publishes a new decision, after each 2027 test and when the FIM’s 2027 regulations appear.
References
- FIM, Decisions of the Grand Prix Commission (Jerez, 26 April 2024), press release 6 May 2024: resources.motogp.pulselive.com/motogp/document/2024/05/06/0491eedd-8c2f-420e-905
- FIM, Grand Prix World Championship Regulations 2026, update 13 September 2026: www.fim-moto.com/en/documents/view/fim-2026-motogp-moto2-moto3-world-championshi
- FIM, Decisions of the Grand Prix Commission (23 September 2026): www.fim-moto.com/en/news/news-detail/article/decisions-of-the-grand-prix-commiss
- Grand Prix Commission, Assen decision on aerodynamic wings (25 June 2016), published by MotoGP.com: www.motogp.com/en/news/2016/06/25/assen-grand-prix-commission-decision/166990
- Grand Prix Commission, decisions of 15 October 2016, “MotoGP Class Aerodynamic Evolution” (published 18 October 2016), published by MotoGP.com: www.motogp.com/en/news/2016/10/18/decision-of-the-grand-prix-commission-in-moteg
- Grand Prix Commission, 2020 Aero Body regulations revised (decision of 15 July 2019), published by MotoGP.com: www.motogp.com/en/news/2019/07/19/2020-aero-body-regulations-revised/154684
- Mat Oxley, Motor Sport magazine, What we know about MotoGP’s 2027 regs (26 January 2026): www.motorsportmagazine.com/archive/article/march-2026/37/mat-oxley-what-we-know-
- Peter McLaren, Crash.net, Yamaha to evolve tri-plane wing for 850 MotoGP era? (23 September 2026): www.crash.net/motogp/news/1105084/1/yamaha-evolve-tri-plane-wing-850-motogp-era
